Description
EB Castworld supplies custom nickel aluminum bronze pump impellers and valve castings against customer-approved drawings, material specifications and inspection requirements. This product page focuses on the Cu-Al-Ni-Fe metal-element system used by recognized cast nickel-aluminum-bronze grades such as UNS C95500 and C95800. It explains how chemistry, casting route, heat treatment, section size, machining and verification must be connected in an industrial RFQ.
This is not a stock-price page and it does not claim that every yellow or bronze-colored casting is nickel aluminum bronze. Final alloy, dimensions, pressure boundary, hydraulic profile, heat treatment, NDT, mechanical properties, corrosion suitability and repair rules must follow the purchaser-approved documents. Any grade substitution, cross-standard equivalence or process change requires written approval.
Product scope: drawing-based pump and valve castings
The intended scope includes customer-designed pump impellers, pump casings or fluid-end castings, valve bodies, discs, seats, guides and related corrosion- or wear-exposed cast components where the purchaser has specified a nickel aluminum bronze. These examples are quotation families, not proof that every pressure class, size, weight, tolerance or safety category is feasible.
| Component | Controlled drawing input | Service input | Quotation boundary |
|---|---|---|---|
| Pump impeller | Vane geometry, eye, diameter, rotation, shaft interface, machining datums and balance requirement | Flow, head, speed, fluid chemistry, solids, temperature and cavitation history | Hydraulic performance and interchangeability remain subject to pump-OEM or authorized engineering approval. |
| Pump casing or fluid end | Pressure boundary, wall, flange, sealing surfaces, flow path, datums and NDT zones | Design pressure/temperature, fluid composition, erosion and galvanic environment | The pressure code, design calculation and proof-test basis must be specified by the purchaser. |
| Valve body or disc | Pressure class, bore, seat geometry, stem interface, flange standard and machining | Media, chloride, velocity, temperature, cycling and shut-off duty | A bronze grade does not by itself certify a complete valve assembly. |
| Seat, guide or wear component | Fits, clearances, contact surface, finish, hardness and mating material | Load, sliding speed, lubrication, contamination and corrosion couple | Tribological suitability requires the complete mating system, not chemistry alone. |

Cu-Al-Ni-Fe chemistry: why four metal elements matter together
Nickel aluminum bronze is a copper-base alloy family in which aluminum, nickel and iron are intentional alloying elements. Aluminum contributes to strengthening and protective-film behavior; nickel and iron influence phase balance, strength, microstructure and casting response. Manganese and controlled residual elements also matter. These roles are interactive, so a single aluminum or nickel reading cannot establish grade identity or corrosion performance.
| Element | Technical role to review | Purchasing caution | Verification |
|---|---|---|---|
| Copper (Cu) | Base metal and continuous matrix for the specified cast alloy. | “Copper alloy” is not a grade. Copper plus named elements and residual limits must meet the governing specification. | Heat analysis and product analysis when ordered. |
| Aluminum (Al) | Major strengthening element and contributor to phase formation and surface-film behavior. | Too little or too much relative to the approved grade changes phase balance and properties; color is not an analytical method. | Laboratory chemistry against the exact UNS/standard range. |
| Nickel (Ni) | Supports mechanical properties and phase control in nickel aluminum bronze. | Nickel content alone does not prove C95500 or C95800 and does not guarantee seawater performance. | Heat analysis; note whether cobalt is included under the governing grade rule. |
| Iron (Fe) | Influences strength, grain/phase constitution and solidification response. | C95800 includes a relationship between iron and nickel; isolated element limits must not be read without footnotes. | Report Fe and Ni together and apply the standard-specific relationship. |
| Manganese (Mn) | Intentional or limited element depending on grade, affecting processing and phase balance. | C95500 and C95800 do not use the same manganese rule. | Use the selected grade range or maximum. |
| Lead and silicon (Pb, Si) | Controlled residuals in C95800 and other applicable specifications. | Low maximum values may require an analytical method suited to the specified level. | Report with method, detection capability and acceptance limit. |
| Other named/residual elements | Can affect cleanliness, welding, corrosion and phase constitution. | Do not silently replace a complete standard composition with a four-element marketing label. | Full certificate and any product-analysis requirement. |
Reference composition ranges for C95500 and C95800
ASTM B148-24 is the current ASTM specification for aluminum-bronze sand castings and includes both UNS C95500 and C95800 among its listed alloys. The composition values below reproduce public Copper Development Association alloy data for purchasing orientation. They are not an EB Castworld proprietary chemistry, and they do not replace the ordered ASTM table, footnotes, test methods, mechanical requirements or customer specification.
| UNS alloy | Cu | Al | Fe | Ni | Mn | Other public limits/notes |
|---|---|---|---|---|---|---|
| C95500 | 78.0% min | 10.0-11.5% | 3.0-5.0% | 3.0-5.5% | 3.5% max | Cu plus the sum of named elements: 99.5% min; public CDA note states the Ni value includes Co. |
| C95800 | 79.0% min | 8.5-9.5% | 3.5-4.5% | 4.0-5.0% | 0.8-1.5% | Pb 0.03% max; Si 0.10% max; Cu plus named elements 99.5% min; Fe must not exceed Ni. |
C95500 and C95800 are not interchangeable merely because both contain Cu, Al, Ni and Fe. Their aluminum and manganese controls differ, and the purchased casting may have different mechanical, heat-treatment, pressure-service or inspection requirements. The RFQ must specify the exact UNS number, ASTM edition, casting process and delivery condition.
How to write the composition line in an RFQ
Use a complete statement such as “UNS C95800 sand casting to ASTM B148-24, chemical and mechanical requirements per the ordered specification, with purchaser supplementary requirements attached.” If an internal customer composition is used, provide every minimum, maximum, analytical method and product-analysis rule. Avoid “C958 equivalent,” “marine bronze” or “same as sample” unless the equivalence basis is fully documented and approved.
Sand casting, investment casting and process-selection boundary
ASTM B148-24 specifically covers sand castings. Sand casting is therefore the primary standards-based route discussed for C95500/C95800 on this page. Pattern, core, gating, feeding, chills, shrinkage allowance, machining stock and section transitions must be developed for the approved geometry. Nickel aluminum bronze can have demanding melt and solidification behavior; process control must address oxidation/dross, gas, feeding and hot spots.
Investment casting may be considered for smaller, geometrically suitable copper-alloy components only after technical review and only under an applicable approved material and process specification. It must not be described automatically as ASTM B148 sand casting. Permanent-mold, centrifugal and continuous-casting standards also have different scopes. The quotation will name the proposed route; the customer must approve any departure from the drawing or purchase specification.
| Route | Potential fit | Main RFQ controls | Important limit |
|---|---|---|---|
| Sand casting | Complex pump/valve shapes and a broad size range | ASTM B148-24 grade, pattern/core strategy, test bars, NDT, machining and repair rules | Surface and dimensional capability depend on geometry and mould/process plan. |
| Investment casting | Smaller complex components where tooling and shell route are feasible | Applicable alloy/process specification, wax/tooling controls, shell, gates, heat and inspection | Do not label the result B148 sand casting unless the governing requirements genuinely apply and are accepted. |
| Permanent mould | Repeat geometry where tooling and solidification design are suitable | Applicable standard, mould design, section response and mechanical-property basis | Properties from one cast form cannot be copied to another without the correct standard. |
| Centrifugal/continuous cast | Rings, sleeves or stock forms rather than arbitrary impeller geometry | Correct product standard, direction, machining allowance and test location | Not a substitute route for every shaped casting. |

Microstructure, heat treatment and section-size response
Compliance is not demonstrated by chemistry alone. Cooling rate, section thickness, phase transformation and any specified heat treatment influence strength, ductility, residual stress, machinability and corrosion behavior. A separately cast test bar may not reproduce every local condition in a thick hub, thin vane or heavy flange. ASTM B148-24 states mechanical requirements are determined from separately cast test-bar castings; purchasers should understand that representation when defining critical-part acceptance.
If a heat-treated condition is required, the order must state it. Furnace charts, load identity, time/temperature and cooling records can be requested. EB Castworld will not publish a universal heat-treatment cycle because applying one recipe to different alloys, sections and specifications can be misleading.
Corrosion, erosion, cavitation and seawater limits
C95800 is commonly associated with seawater and marine components in Copper Development Association application data, including propeller and valve uses. That does not mean every C95800 casting is immune to corrosion, erosion-corrosion, cavitation, galvanic attack, microbiologically influenced corrosion or deposit effects. Fluid velocity, aeration, chloride, sulfide, ammonia, pH, temperature, solids, stagnant exposure, surface condition and mating metals can change performance.
The purchaser must approve the alloy for the actual medium and operating envelope. A pump impeller additionally requires hydraulic and cavitation review. A valve body requires the applicable pressure design and leakage/seat criteria. When dissimilar metals are connected in an electrolyte, the galvanic couple, area ratio, electrical continuity and cathodic-protection system should be reviewed by the responsible corrosion engineer.
| Environment input | Why it belongs in the RFQ | Decision boundary |
|---|---|---|
| Complete fluid chemistry | Chloride alone does not describe sulfide, ammonia, oxidants, pH or contaminants. | Material approval belongs to the owner/OEM/corrosion authority. |
| Velocity and solids | Erosion can remove protective films and interact with corrosion. | No corrosion-rate or life claim is made without representative evidence. |
| Temperature and aeration | Change reaction kinetics and surface-film conditions. | State normal, start-up, cleaning and upset conditions. |
| Mating metals and cathodic protection | Influence galvanic current and hydrogen-related concerns. | Review the complete assembled system, not the isolated casting. |
| Cavitation/operating point | Hydraulic instability can dominate local surface loss. | Changing alloy is not a substitute for correcting pump selection or operation. |
Machining, balance, pressure boundary and fixing
Specify as-cast, rough-machined or finish-machined supply. The approved drawing should identify units, datums, fits, geometric tolerances, surface finish, sealing faces, pressure surfaces, threads, keyways, bores, minimum wall and areas where metal removal is prohibited. If the 3D model and 2D drawing differ, state which controls.
Impellers require an approved balance standard/grade, balancing stage and permitted correction method. Valve and pump pressure castings require the applicable pressure-design basis, NDT and pressure/leak test requirements. Fixing details, fastener material, preload, isolation, seat installation and running clearance remain part of the equipment design and must not be inferred by the casting supplier.

Inspection and quality-document package
| Inspection | Define before order | Evidence |
|---|---|---|
| Chemical composition | UNS alloy, ASTM edition, element limits, heat/product analysis and method | Traceable chemistry report |
| Mechanical properties | Test-bar basis, condition, tensile requirements, hardness and sampling | Mechanical test report linked to heat/lot |
| Visual/dimensional | Drawing revision, datums, CTQ dimensions, surface acceptance and sampling | Dimensional and visual report |
| NDT | PT/RT/UT or other method, coverage, stage, acceptance standard and personnel | Signed NDT report and indication disposition |
| Pressure/leak test | Code, medium, pressure, hold, temperature, safety and acceptance | Test certificate when ordered |
| Impeller balance | Standard, grade, configuration, correction and report | Balance certificate |
| Traceability | Part marking, heat, lot, heat treatment, inspection-document type and language | Release dossier and approved deviations |
Weld repair and fabrication boundary
Weld repair must be treated as an order decision, not a routine cosmetic operation. The governing standard and purchaser must define whether repair is prohibited, permitted or approval-controlled. Where permitted, specify WPS/PQR qualification, filler metal, preparation, preheat/interpass limits, post-weld treatment, repair map, NDT and final acceptance. A repaired pressure boundary may require additional approval and testing.
Copper Development Association data lists gas-shielded arc welding as suitable for C95500/C95800, but a generic suitability rating is not a qualified procedure for a specific casting. Geometry, restraint, chemistry, heat treatment and service control the actual procedure.
Failure evidence and controlled replacement trials
For a replacement RFQ, provide the original certificate if available, drawing, service history, photographs and a wear/corrosion map. Record cracking, dezincification-like discoloration, pitting, erosion grooves, cavitation-like attack, seat leakage, galvanic deposits, impeller imbalance or dimensional loss. Avoid reverse engineering solely from a worn sample because the current dimensions may not represent the original hydraulic or sealing profile.
Do not convert one field result into a universal guarantee
If changing from another bronze or stainless alloy, use a controlled trial with the same equipment, fluid, operating point, inspection interval and removal criteria. Document dimensions and mass before/after service. A successful trial supports that defined duty; it does not justify a universal life-extension or percentage-saving claim.
RFQ checklist
- Component name, equipment maker/model, part number, drawing and revision.
- 2D drawing and 3D model with governing-document priority.
- UNS C95500, C95800 or other exact alloy; ASTM B148-24 or other complete standard/edition.
- Required casting process and any permitted alternative route.
- Fluid chemistry, temperature, pressure, velocity, solids, cavitation and galvanic context.
- Heat treatment, mechanical properties, hardness and test-bar/product-analysis requirements.
- Machining, datums, fits, sealing surfaces, balance and minimum-wall requirements.
- NDT, pressure/leak test, witness/hold points and acceptance standards.
- Part/heat/lot traceability, inspection certificate and report language.
- Quantity, destination, packaging and commercial terms; do not assume stock or lead time.
Related EB Castworld pages
- Aluminum Bronze Castings
- Aluminum Bronze Butterfly Valves
- Investment-Cast Bronze Butterfly Valves
- Bronze Castings Manufacturer
- Sand Casting Parts Guide
- Precision Casting Process Guide
- Quality Assurance and Factory Capability
Technical and safety boundary
The purchaser, equipment OEM or authorized engineer must approve alloy selection, pressure design, hydraulic geometry, corrosion compatibility, welding/repair, balance, installation and acceptance criteria. EB Castworld does not promise seawater immunity, pressure certification, service life, energy savings, delivery time or interchangeability without approved requirements and evidence.

