Description
Featured image: external reference, not an EB product photograph or customer project. Full source and license details are below.
EB Castworld accepts drawing-based enquiries for 18CrNiMo7-6 (1.6587) carbon-chromium-nickel-molybdenum forged pinion shafts, gear blanks and transmission rings intended for customer-controlled carburizing and finishing routes. Supply can be an annealed forged blank, rough-machined blank, heat-treated semi-finished component or finished gear only when the complete drawing, case-hardening specification, gear data and inspection plan are agreed. This is not a stocked gear, and no torque, case depth, accuracy grade, fatigue life or interchangeability is promised from the steel designation alone.
Send Drawings for Quote | RFQ Email: sales@ebcastworld.com | Factory Capability
The gearbox or equipment designer owns gear rating, tooth geometry, load spectrum, bearing layout, lubrication, carburized-case design and final approval. Final material, forging route, stock, heat treatment, dimensions, tooth finishing and installation must follow the customer-approved drawing and purchase specification.
1. Define the forged product and manufacturing split
A forged gear blank is not a finished gear. The RFQ must say whether EB supplies a ring, solid blank, integral pinion shaft or finished component, and who performs carburizing, quenching, grinding, balance and final gear inspection.
| Supply scope | Required definition | Responsibility boundary |
|---|---|---|
| Annealed forging | Forging envelope, stock and material condition | Buyer performs all heat treatment/machining |
| Rough-machined blank | Datums, cleanup dimensions and UT condition | Remaining stock and later distortion belong to agreed party |
| Pre-machined carburizing blank | Tooth/root allowance and masking features | Heat treater follows customer case specification |
| Finished pinion shaft | Full journal, spline/tooth and surface requirements | Complete controlled design required |
| Replacement from sample | Approved dimensional survey and mating-gear data | Owner validates original geometry/interchangeability |
A worn tooth or bent shaft cannot define the original design. Reverse engineering should combine controlled measurement, material verification, failure evidence and approval by the equipment owner.
2. 18CrNiMo7-6 metal composition and designation boundary
Ovako’s current 18CrNiMo7-6 material data sheet describes a case-hardening steel with high toughness and notes several cleaner/tighter supplier variants. The composition table below summarizes the broad reference ranges shown for one listed variant. It is a steelmaker reference—not a universal EB guarantee—and the purchaser must state the governing EN ISO 683 series or project specification.
| Element | Ovako reference range, mass % | Purchasing significance |
|---|---|---|
| Carbon, C | 0.15–0.21 | Low-carbon core chemistry designed for a subsequent case-hardening route |
| Silicon, Si | 0.10–0.40 | Controlled constituent; supplier variants may be tighter |
| Manganese, Mn | 0.50–0.90 | Supports hardenability and steelmaking response |
| Chromium, Cr | 1.50–1.80 | Major case-hardening alloy element |
| Nickel, Ni | 1.40–1.70 | Major alloy addition associated with core toughness/hardenability |
| Molybdenum, Mo | 0.25–0.35 | Controlled addition for hardenability/tempering response |
| Phosphorus, P | 0.015 maximum in the cited variant | Restricted residual; governing grade may differ |
| Sulfur, S | 0.015 maximum in the cited variant | Supplier variant control; machinability variants can differ |
Ovako explicitly describes multiple variants with tighter ranges and different cleanliness or sulfur control. Do not present one steelmaker’s 159A/159B/159Q/159X/159S data as the universal grade guarantee. State the exact product standard, hardenability band, cleanliness, residual limits and certificate requirements.
3. Why the elements support—but do not define—the case
Carburizing introduces carbon at the surface under a controlled thermal/chemical cycle; quenching and tempering then develop the required case and core condition. Chromium, nickel and molybdenum affect hardenability and response, but heat chemistry alone cannot prove effective case depth, retained austenite, carbide condition, distortion or residual stress.
| Evidence | What it supports | What it cannot prove alone |
|---|---|---|
| Heat analysis | Base-steel composition | Finished case depth and hardness profile |
| Jominy/hardenability data | Response of a standardized specimen | Exact response of every gear section |
| Furnace chart | Recorded cycle for the load | Carbon profile without verification |
| Microhardness traverse | Local hardness versus depth | Whole-gear uniformity without sampling plan |
| Metallography | Case/core features at sampled position | Gear rating or fatigue life |
The customer must specify carburizing potential, temperature/cycle control, quench, tempering, effective case-depth definition, surface/core hardness and sampling locations—or provide the controlling heat-treatment specification.
4. Forging route, reduction and grain-flow planning
Forging should establish a sound blank with stock for heat treatment and machining. Ring rolling may be considered for suitable hollow gear blanks; open-die forging can suit solid disks, shafts or large rings. Integral pinions need a route that addresses shaft transitions, test extensions and fiber flow.
| Product geometry | Candidate route | Review inputs |
|---|---|---|
| Rolled ring blank | Ring rolling from pierced preform | ID/OD/height, stock and test location |
| Solid gear disk | Upset/open-die forged disk | Hub/rim section, reduction and machining envelope |
| Integral pinion shaft | Drawn shaft with forged journals/gear section | Transitions, centerline quality and test prolongation |
| Segmented/assembled gear | Not assumed equivalent to one-piece forging | Approved joint design and separate specifications |
Route feasibility depends on final size, mass, equipment capacity and acceptance. EB confirms scope after drawing review; this page does not claim every diameter or weight.

5. Carburizing allowance and distortion planning
Machining stock must support cleanup after forging and any heat treatment. For carburized gears, tooth pre-machining, copper plating/masking, grinding stock, datum design and distortion compensation require coordination with the heat treater and gear manufacturer.
| Control | RFQ input | Failure avoided |
|---|---|---|
| Case pattern | Surfaces to carburize, mask or machine away | Unwanted brittle/high-hardness zones |
| Effective case depth | Definition, target/range and locations | Ambiguous hardness-profile acceptance |
| Surface hardness | Scale, range and decarburization rule | Grade-name-only acceptance |
| Core properties | Test location and requirements | Hard case with inadequate core condition |
| Grinding stock | Per flank/journal and final finish | Failure to clean up distortion |
| Stabilization | Any subzero/stress-relief step | Uncontrolled dimensional change |
Do not improvise case depth from gear size alone. Tooth contact stress, bending stress, module, root geometry and load cycles belong to the gearbox design authority.
6. Gear geometry and drawing inputs
When teeth or splines are included, supply the governing ISO, AGMA, DIN or OEM standard and edition. Provide module/DP, tooth count, pressure angle, helix angle/hand, profile/lead modifications, reference diameter and measuring method. State the required accuracy grade and reported parameters.
| Gear input | Required format | Why needed |
|---|---|---|
| Tooth system | Standard, module/DP and pressure angle | Defines cutting geometry |
| Helix | Angle, hand and reference convention | Prevents opposite-hand manufacture |
| Modifications | Profile/lead slope, crowning and end relief | Links design intent to inspection |
| Tooth thickness | Measurement method and limits | Establishes backlash target |
| Accuracy | Standard, grade and parameters | Defines process/inspection capability |
| Mating gear | Drawing, center distance and condition | Supports contact and system review |
“Make like sample” is not enough. Worn tooth flanks and historical repairs do not reveal intentional microgeometry.
7. Journals, keyways, splines and fatigue-sensitive transitions
Pinion shafts combine tooth loads with bearing and coupling interfaces. Define journals, shoulders, fillets, oil holes, keys/splines and runout from functional datums. Do not enlarge a keyway or blend a fillet for shop convenience without design approval.
| Feature | Drawing control | Inspection evidence |
|---|---|---|
| Bearing journal | Fit, cylindricity, finish and datum | Dimensional/roughness report |
| Gear-to-journal relation | Runout and position | CMM or between-centers report |
| Fillets | Radius/profile and no-undercut zone | Profile and surface examination |
| Keyway/spline | Standard, fit, orientation and root | Gauge/measurement report |
| Center holes | Retain/remove and protection | Final visual/dimensional check |
Measurement support and temperature affect long shafts. State the inspection setup, datum simulator and any customer gauge requirement.
8. Cleanliness, inclusions and ultrasonic examination
Ovako identifies variants with elevated cleanliness controls, showing why the base designation alone is insufficient. If fatigue risk demands cleanliness limits, define the method, sampling, rating system and acceptance. Do not request “aircraft quality” without a measurable specification.
For forged blanks, the ASTM A388/A388M ultrasonic examination page is a useful method reference where contractually appropriate. Specify examination stage, scan surfaces, coverage, calibration, recording and acceptance.
| UT/cleanliness item | RFQ requirement | Limitation |
|---|---|---|
| Examination stage | Annealed, normalized or rough machined | Surface and structure affect testability |
| Coverage | Rim, hub, shaft, journals and excluded zones | Geometry can create inaccessible areas |
| Calibration | Block/reflector and frequency | Must match agreed standard |
| Recording level | Amplitude/length/location | Not automatically a rejection level |
| Inclusion rating | Test method and sampling | Local specimen does not map whole forging |
9. Mechanical tests and heat-treatment verification
Define tensile, impact, hardness and hardenability tests with specimen orientation, location, heat-treatment condition and frequency. A forged test prolongation should represent the ordered condition as specified, but it cannot reproduce every local tooth-root stress.
| Test | Purchasing question | Required record |
|---|---|---|
| Tensile | Core condition, orientation and values | Full stress-strain results if requested |
| Impact | Temperature, specimen direction and minimum/average | Individual values |
| Hardness | Pre-carburizing or final; locations and scale | Hardness map |
| Case traverse | Effective/total depth definition and load | Microhardness graph |
| Metallography | Case, carbides, grain and decarburization | Images plus preparation/magnification |
Acceptance criteria and retest rules must precede production. Hardness conversions require purchaser approval and a stated conversion standard.
10. Tooth finishing and final inspection
Carburized teeth may require grinding or another approved finishing process. Define grinding-burn inspection, surface examination, lead/profile measurement, pitch, runout, tooth thickness and contact testing. The required checks depend on the gear standard and risk.
| Final check | Contract definition | Output |
|---|---|---|
| Profile and lead | Parameters, evaluation length and grade | Gear inspection chart |
| Pitch/runout | Standard and tolerance | Tabulated results |
| Tooth thickness | Span/ball/other method | Measurement report |
| Grinding damage | Approved method and acceptance | Inspection report |
| Contact pattern | Mating setup, load and marking compound | Photographs/report |
| Balance | Condition, speed and grade if required | Balance certificate |
A compliant blank does not guarantee compliant teeth when another supplier performs heat treatment or grinding. Define the transfer condition and final acceptance owner.
11. Traceability, marking and packaging
Link steel heat, forging, heat treatment, tests, machining and final inspection. Marking must survive operations or be transferred under control. Avoid stamping fatigue-sensitive surfaces unless the drawing permits it.
| Dossier item | Traceability link | Buyer decision |
|---|---|---|
| Material certificate | Heat and 18CrNiMo7-6 specification | Certificate type |
| Forging record | Forging ID, route and heat | Reduction evidence |
| Heat-treatment record | Load and part IDs | Review/hold point |
| UT/test reports | Sample/zone and part ID | Acceptance authority |
| Gear report | Drawing revision and serial number | Required parameters |
| Packing release | Preservative and protected surfaces | Export packaging |
Support heavy rings and shafts to prevent transport damage. Protect tooth stock, journals and centers. Temporary protection must be compatible with later carburizing or cleaning.
12. Safety and engineering boundary
Gear trains contain crushing, rotation, stored energy and lifting hazards. Follow the OEM manual, engineered lifting plan and site isolation process. The OSHA hazardous-energy-control resource provides general context; local rules govern work.
This page is not a carburizing recipe, gear-rating calculation, lifting procedure or installation instruction. Competent personnel must approve heat treatment, inspect mating components, set backlash/contact and verify lubrication before service.
13. RFQ checklist for 18CrNiMo7-6 forgings
Minimum package for technical review
- controlled 2D drawing and 3D model with revision;
- forging envelope, finished dimensions, mass and stock;
- 18CrNiMo7-6/1.6587 standard, edition and supplier-variant restrictions;
- melt route, cleanliness, hardenability and residual-element requirements;
- forging route, reduction and test-prolongation requirements;
- annealed/preheat-treated delivery condition;
- carburizing, masking, case depth, hardness and core-property specification;
- tooth/spline standard, geometry, modifications and accuracy grade;
- UT, MT, grinding-burn and dimensional inspection plans;
- mechanical tests, metallography and case traverse requirements;
- certificate, record-book, marking, preservation and packing needs;
- quantity, forecast and written deviation approval route.
14. Related products and quotation route
Compare quotations only after aligning the supply condition. One supplier may quote an annealed forging, another a carburized and ground pinion, and a third a rough blank without UT or mechanical tests. These are different deliverables. Ask for a compliance matrix and a route sheet showing where each test and hold point occurs.
| Comparison item | Clarification | Risk if unclear |
|---|---|---|
| Steel condition | Annealed, normalized, pretreated or carburized | Properties and machinability are not comparable |
| Forging scope | Ring, disk or integral shaft; stock and reduction | Hidden material removal and quality assumptions |
| Heat treatment | Who owns carburizing, distortion and rework | Responsibility gap after case hardening |
| Gear finishing | Cut, shave, grind or inspection-only scope | Accuracy price compared against a blank |
| Tests | UT, hardness, case traverse, metallography and gear charts | Incomplete acceptance evidence |
| Tooling/gauges | Supplier or customer-owned and calibration status | Repeatability and schedule uncertainty |
The quotation should state the drawing revision, standard editions, quantity, inspection documents, exclusions and validity of technical assumptions. Any proposed alternate steel or heat-treatment route requires written customer approval. EB does not treat a “similar” SAE or DIN designation as automatically equivalent. Delivery is planned after the buyer approves the manufacturing split and supplies required proprietary gear data; this page does not advertise stock or a fixed lead time.
For a different alloy and application, review the 34CrNiMo6 forged coupling hub product and 42CrMo4 forged conveyor drive shaft product. For fit and fretting information, see the coupling hub bore-fit and keyway guide. None authorizes grade substitution.
Submit drawings through Contact EB Castworld, email sales@ebcastworld.com, and review factory capabilities. EB will confirm feasible scope, inspection documents and quotation assumptions. Final manufacture remains controlled by the approved drawing and purchase specification.

Image sources and reuse permissions
- Featured image: Image title: Crawler-Transporter 2 undergoing gear box maintenance (KSC-2014-1892).jpg. External NASA crawler-transporter maintenance context; not an EB project, product or 18CrNiMo7-6 forging record. External reference photograph/micrograph; not an EB Castworld project or test record. Author: NASA/Dimitri Gerondidakis. Source on Wikimedia Commons. Public domain. Downloaded as a Wikimedia Commons display-size derivative; no other pixel editing. WordPress may create additional display sizes; license retained.
- Figure 1: Image title: Gear pattern – San Francisco Cable Car Museum – DSC04046.jpg. External museum wooden pattern for a cast herringbone gear; not a forged EB blank or reusable customer geometry. External reference photograph/micrograph; not an EB Castworld project or test record. Author: Daderot. Source on Wikimedia Commons. CC0. Downloaded as a Wikimedia Commons display-size derivative; no other pixel editing. WordPress may create additional display sizes; license retained.
- Figure 2: Image title: Gears large.jpg. External agricultural spur gears; material, heat treatment and manufacturer are not verified as EB or 18CrNiMo7-6. External reference photograph/micrograph; not an EB Castworld project or test record. Author: Jared C. Benedict (user Redjar ). Source on Wikimedia Commons. CC BY-SA 3.0. Downloaded as a Wikimedia Commons display-size derivative; no other pixel editing. WordPress may create additional display sizes; license retained.

